PCTC Screen Protector fit for Sony alpha 1 a7II A7III a7SII a7SIII a7RII a7RIII a7RIV RX100VII RX100VI RX100V RX100IV RX100M2 A9II,ZV-E10 RX10IV ZV-1 ZV-1M2,3 Packs Tempered Glass Screen Protector

Like most Sony cameras of the era, the used RX10 I picked up recently was suffering from the factory screen protector coating going bad/delaminating so it was in need of a replacement. I've done it on multiple camera models now over the years so it was simple, just peel off the factory film and replace with a nice tempered glass screen protector for a perfect and refreshed screen. These screen protectors fit perfectly with precise tolerances and go on super well if you know what you're doing when cleaning and applying! Photos are the before with the failing factory screen cover, and after with the new screen protector installed to show the fit.

This is a very good quality screen protector, fits extremely well, has enough thickness to make me feel comfortable that the screen is protected from minor incidents. Does not interfere with visibility and aligned well over screen. My RX-100 VA does not have a touchscreen function so I cannot confirm that function.

I used these as a screen protector for my new Sony DSC RX10M4. The fit was spot-on, no overhangs, and virtually invisible when installed. Touch screen works perfectly. Installation, if you are careful, is simple. Just take your time, clean everything thoroughly, and use the blue "grab" stickers. Simply attach them to the midpoint of the left and right edges of the protector, position carefully under good lighting, and lower in place. Mine adhered perfectly. Great price and great quality.

After some research I decided on the PCTC Screen Protector for my Sony A7rIV. It had good reviews, a great price, and came as a three pack. I’ve used a number of camera screen protectors over the last 10 years. Some cost over $20 for a single piece of film. All I had tried were very touchy to install, frequently requiring rework to take care of a trapped piece of dust. You also had to roll them on carefully working out the air as you applied them. First time success was almost zero. The first surprise of the PCTC product was it came in a nice little wood grained hard sided hinged box. The kit was very complete. A visual instruction card, two stage wet/dry wipes, stickers to pull off the last vestige of dust, and the three foam wrapped screen protectors were included. The big surprise came when I applied the actual screen protector. It is a stiffer, more glass pane like material (but very thin). After you peel off the backing sheet, you carefully lay it down on the camera screen. This was relatively easy to do, since the screen was rigid. I lined up one short edge and let fall on to the screen. Once laying on the screen, the protector could be gently pushed from the edge to fine tune the alignment. I was now expecting to have to work out the trapped air, but before I could start, I watched the protector quickly adhere to the screen with the air vacating by itself. A light rub with the dry wipe and it was done. No fuss and a perfect job. Never had that happen before. We’ll see how it holds up over time, but the protector seems very secure and is pretty much invisible. The screen touch functions of the camera work just fine. Overall an excellent value for both performance and price.

You get three of these in the package and that is quite a bargain. On my RX100VI camera I found that it was truly difficult to fit this screen properly. It is cut to the exact size of the screen and if any of it overlaps the border by even the tiniest fraction the protector will eventually lift off. It will seem to be well atached, but it actually isn't. You can not even see this timy bit of misalignment with the naked eye. I had to use a headband mounted magnifier to position this thing perfectly making sure all edges are clear of the border and then it adhered perfectly. Adding to the frustration, the little tab that allows you to peel off the backing is not positioned at the corner. It does not pull off the backing at all. I had to use a sharp tool to lift the corner and then use scotch tape to pull the corner up and peel off the backing. Still, with all that, no dust. It's a fine protector but it loses points for being hard to separate from the backing and being just a tad large to fit without eyesight assistance.

Fits the Sony a7iii screen perfectly. Barely know it’s on the screen but good protection from scratches and damage since there is no way to cover it otherwise

A great idea to protect an LCD screen!

Easy installation, get it wiped a little and remove the dust using the pack they include together with the protective glass, looks amazing while equipped on the camera screen, no vignetting or other side effects, haven't tested the real durability but still looks amazing, doesn't slip while putting pressure or touching, overall, good product...

This product is as advertised and arrived in a sturdy hard case. It fit perfectly on my Sony a7RIII. Follow the instructions on the provided card and you will have no trouble installing it. It comes with dust removing stickies, a wet and dry wipe and guide stickers so you can align it properly to your screen.

Viene con 3 cristales, con una toalla húmeda y una seca para limpiar la superficie (un set por cada cristal), además de un adhesivo para eliminar el polvo, para mi la instalación fué sencilla y el tamaño queda perfecto para la a7rii que no se nota que está ahi.

Le quedó muy bien a Sony RX100M2, no afecta visibilidad y protege bastante contra arañazos y rayones

Instructions suck. I’d recommend looking for a video to see how it’s done. But it’s super easy once you know how. Other than that, the product itself seems good. The attached photo is my before and after.

The screen protector is as advertised and fit perfectly on my Sony A7 III. It arrived in a pack of 3, and had a few dry and wet wipes to prep the screen as well as a sticker thingy for grabbing any dust particles off the screen as well as screen guide stickers to use so that you don't accidentally touch the back of the glass while applying it. Putting it on the screen was pretty straightforward. I got a few tiny air bubbles on the edge of the screen but they don't bother me and I could probably get rid of them if I reapply it carefully so that it's aligned a little better. I was a little worried about the touch sensitivity, or the screen feeling not as smooth, but thankfully that wasn't the case. The touch works perfectly and the feels just as smooth. One thing that does bother me a tiny bit is that the tempered glass is a little more prone to the fingerprints compared to the actual screen, though you only see it if the screen is off and the light is hitting the screen at an angle.