Uniflasy 7635 Flavorizer Bars and 69785 Grill Burner Tubes for Weber Spirit I & II 200 with Front Control, Spirit E210, E220, S210, S220, for Weber 15.3 Inch 7635 Flavor Bars and 69785 Burner Pipe

I have a Weber Spirit E210. I have not ever repalced the gas burner tubes before. Well until today. Nothing went boom. And after intallation I let it burn for 20 minutes. They look brand new, and I did it in 30 minutes. Perfect fit, and weight and look was as good as the originals at least. Flame was just right.If you decide to put them in a few thoughts:I went to YouTube and watched basic videos. I put my brand and model number in the search. As you know some videos are better than others. I watched three.TAKE PICTURES with your phone so when it is time to re-assemble you can see exactally what you did. And it's fun to make your spouse look at them to show your expertise.Relax and don't rush.On my grill, I had to take the knobs off front, and the cover off the front. I had pictures if needed to see what I did. Mine was simple, I did not need them. I feel so smug.In the backside of the grill there are two screws to hold the gas pipes in. After years of cooking and grease, and probably because the heat too I could not budge thm with a screwdrver. I used a socket wrence over the screws and it worked great. They provide new screws. (An adjustable wrench of vice grips might work fine.)It is tricky sliding the gas tubes out. I lifted the end screwed up, stuck my tonge out the left side of my mouth, and, wiggled my toes. It's tight, but with a bit of adjustment they came out.It's a tad cumbersome to put the new ones in, but went easy. Be sure to have the tube with the slide to hold the self starter on the right side.Then put screws back in.Reassemble avoid anything that makes a boom

Burners seem sturdy and well made. Easy to replace on my Weber Spirit 2 grill except the 2 new screws that attach the burners to the back of the grill seemed slightly larger than the original holes and had a hard time getting them to screw in (would have used the old screws but they were pretty rusted). ***You shouldn't have to take the front panel off to replace the burners. I watched a you tube video that showed how to do it without removing the front panel. Just slide the burners into the holes.*** Works great. Job would have taken roughly 15 minutes to do but I cleaned the whole grill which was harder than replacing the burners. I'm a 76 year old woman. If I can do it myself most people should be able to do it.

I ordered the cast iron grates, burners, and flavor bars. They are really nice quality and a very reasonable price ( I bought a package deal). Easy to install and didn’t take much time at all. The inside of my spirit II LOOKS NEW! Did a quick burn off and cooked some burgers. Cooked evenly and they turned out great!

Nice package that includes the flavor bars, burners, and a new ignitor. The only complaint I has was the gas burners are a bit shorter and the flat tabs on the end that go under the screws to hold them in place is thinner than the originals. This allows the bars to move around if you move the grill. I need to get a good SS shim to make up the thickness difference but for now I was able to lift the burner up a bit and slide it under the screw and carefully tighten to hold it. Overall, for the price, it gets me back to grilling again which is always a good thing!

Perfect fit for my Weber Spirit 310. The existing burners were not too bad but the connector tube was shot. This deal of all 3 burners + new rear connector tube was cheaper than buying the connector tube alone.I cannot tell the difference in quality between the originals and these new ones. I saw reports of some saying they were too short but these were the perfect length.With a good power wash, new burners and deflectors hope to get another 5 years out of this BBQ.

In addition to receiving the correct parts for my grill, the directions provided were excellent. Also totally dismantling the grill front provided me the opportunity to clean everything and to tighten frame screws that come loose over time.

Installed in less than 10 minutes, all parts were in the box INCLUDING the stainless steel screws . The burners work great and I think the grill is now good to go for another 5 years.

Nice items and a great fit