PureluxPop Up Drain Stopper with Overflow for Bathroom Faucet Vessel or Vanity Sink, Matte Black Finish

What a mess this thing created in the project! Admittedly, the sink is builder grade from the mid 90’s, so not top of the line, but neither is the drain (not most expensive or highest rated). So, here goes... 1. the drain body did not fit down into the sink divet; 2. The drain tailpiece was not long enough; 3. Cannot purchase a 1.25 drain tailpiece at local stores, code is now 1.5 inches.1. The drain body fit in the hole but did not rest in the “dimple” or divet at the bottom of the sink. This is NOT what caused the tailpiece to be too short since it couldn’t have made more than .25” difference.2. Apparently, drain tailpieces come in three sizes, 4”, 6”, and 12”. 6” is the most common in the local stores. The tailpiece on this drain was 5”. Ah -ha moment, that’s why most drains in the store come with a 12” tailpiece....then it works for everyone (when cut down and this is usually not hard to do).3. So, we thought, well for a couple bucks we can just get a pvc tailpiece. Nope. The stores do not sell 1.25” tailpieces. Standard is now 1.5”. Michigan plumbing code P2703.1. Minimum size—Fixture tailpieces shall not be less than 1 ½ inches (38mm) in diameter for sinks....So, the drain was teturned. Measure the length of your current tailpiece before purchasing this.4.

I read many of the reviews and spent about 4 hours trying to use more plumbers putty here and there but finally had to nuke it with Silicone. Used plumbers putty on the top part of the sink because it has a larger than normal opening. However, leaked like a submarine with a screen door from the rubber washer below the sink. Open up the picture and use with the below text:USE CLEAR SILICONE!!! (do not used silicone plus caulking, just good old 100% silicone)Silicone the crap out of the top of the rubber ring (1)Silicone the bottom of the since where the rubber ring slides up to (2), and then slide up as far as you can by hand.Silicone the top of the threaded brass washer that tightens the rubber ring to the bottom of the sink.Unthread the extension tube (4) and silicone the threats at the top and the top washer inside the tube.WAIT 12 Hours!

Ordered 2 stoppers for master bathroom in March for renovation. Installed in May after countertops, etc. Both looked great upon installation. However, one’s finish is peeling and looks 10 years old. I’ve looked everywhere trying to find way to contact company for opportunity to resolve and hate resorting to reviews but at this point I’m irritated. The is no difference in the way the sinks have been used as we each used both sinks during process. Both have been cleaned the same, etc. I either need to get another one of these and hope it works like the first one or get two of a different brand. I am open to updating my review if we can get this resolved as there is always one in 1000 that might be like this and seems to be the case based on current reviews, but for me it is 50% fail rate right now:(

I recently had the displeasure of completely renovating my bathroom in a house that's close to 80 years old. Tear out to studs, all of which were out of plumb and out of square...along with the floor. Everything I've done has been a struggle. Stuck galvanized plumbing fixtures, petrified studs that stripped drywall screws...you name it. Along comes this drain assembly. The design was intuitive. Just by eyeballing it I could see how it installed. Checked the instructions and yep...that's it. I used 100% clear silicone where it meets the sink, and again where the bottom gasket meets the sink dropout (below the overflow level). It felt very well machined, no struggles with threads, gaskets...anything. As other reviews have stated, make sure you purchase the correct drop out for your type of sink. The one pictured (with the holes between the gasket) are designed for sinks with overflows. If you buy one of these and try to use it with a sink that has no overflow. You're going to have issues. Great product.

Water doesn't fully drain from the sink. I added two picture attachments. First picture shows the drain after the water was turned on and it leaves water in the sink. Second picture shows where I twisted the popup assembly off (this is for clean out, etc) to show that the water still does not drain. The chrome washer is sitting too high (it is not flush with sink height) therefore the water just pools there and cannot drain.Turns out that all sinks drain sizes are not the same. This product fits sink drain diameter of 1-5/8” to 1-3/4”... My sink drain might need a 1-1/2" drain assembly.... That extra 1/8" evidently causes a small amount of water remain in the sink and doesn't drain completely. I had no idea that different sinks had different size drains. It was only after the drain assembly was fully installed that I noticed the problem. I was replacing an existing working drain assembly and faucet with a motion sensor faucet.I emailed the vendor and they recommend a different size drain stopper assembly. They offered a refund, but I'm still out the costs and time that it took for installation.

The only reason this was not a 5 star was what I think is an installation flaw. I've installed many sink drains over the years and never had a leak from the flange above the sink. After installing the drain just using the enclosed washer, it leaked no matter how much I tightened. I disassembled and used both plumbers putty and the enclosed washer, as the instructions suggested. Still leaked, but more slowly. I disassembled again, cleaned everything, took off the washer like every other drain I have installed, and used only plumbers putty. Like I expected, no leaks. Other than this, the drain is high quality and looks good.

I can't believe the quality of this pop-up considering it was only $21 delivered. The plastic one that came with my sink would not stop dripping even after trying all of the tricks. This assembly comes with silicon seals for both the top and bottom that mated perfectly with my sink. No messing around with plumber's putty. I only needed a gentle turn of the brass nut just beyond hand tight and done. No drips. Very nice satin nickel finish. Fantastic item.

Super easy to install. Comes well packaged with the button top protected from scratches.Putting this in took about 15 minutes and it works very well right from the start. I suggest using teflon tap around any threads for a little extra leak protection.I don't anticipate any issues from this product. Great price and excellent value.

I am very pleased with this item. I have never done any plumbing before, so I wasn’t sure I would be able to do it myself, but it was easy to do an great quality. I couldn’t be happier

Easy install, works and looks as it should

Came on time , good quality materials, just way to large for an American standard bathroom sink.