Home Intuition2-Pack Leader and Gutter Guard from Leaves, Twigs, Branches Plastic Mesh Guards Leaf Protector 6" inch Wide 40' Feet Long Total

It took me a few tries to install. I did not use the plastic holders as I found them troublesome and instead chose to slip under shingles and secure the ends with a self tapping stew. It really wasn't that bad at all.

After this winter, I will know better if these hold down and don’t get blown out by the wind, but installation was fairly easy and they seem to be durable. Only time will tell.

It is great stuff and I'm glad it's still available. I don't use it on the gutters but under the deck on the back of the house to keep birds from nesting. It is difficult to staple it in place, but it works great!

Cheaply made. Clips do not stay attached to plastic screen. When layed out edges do not stay flat and this allows debris to slide under into gutter.

While this product is definitely easy to work with, the performance and constant repairs and adjustments that are required to keep it functioning are almost as tedious as cleaning out a clogged gutter. The clips that are provided when in the Florida sun fail to the point that the screen actually gets pushed completely into the gutter itself, depositing any trapped contents into the gutter itself, rendering it useless. I will say on the side where there is simply some bloom residue, no leaves or twigs, it does a fair job of keeping out a majority of said but that’s not what clogs the gutter.I’m going to throw this product out and try a competitor to see if it’s any better or Lesf Guard is an industry leader as they declare.

My property is surrounded by pines. The gutters currently installed are complete trash and I'm avoiding major upgrades at the moment. After weeks/hours of research my long-term options are expensive ones, new gutters with premium metal guards.No easy solutions exist for pine needles. Either the product you are installing has too small of holes (water will flow over your gutters) or too large (pine needles with get stuck in the guard) … and the most important problem: maintenance. No product exists that overcome these challenges + keep the cost low. So I’m creating that solution.My Build:Magnetic strip https://www.amazon.com/gp/product/B0799QD1MK/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1Half inch self tapping screws: https://www.amazon.com/gp/product/B008SPIQ2I/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1Zip tiesand the mesh product reviewed today https://www.amazon.com/Home-Intuition-Gutter-Plastic-Guards/dp/B07BDPP1KB/ref=asc_df_B07BDPP1KB/?tag=hyprod-20&linkCode=df0&hvadid=241973991106&hvpos=&hvnetw=g&hvrand=2381773061534257327&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9005825&hvtargid=pla-473522272714&psc=11. Drill small pilot holes for the self tapping screws index to thumb length all the way down the gutter.2. Repeat pilot holes through the magnetic strip.3. Zip tie the magnetic strip to the mesh, this side will face your home.4. Secure the mesh using the self tapping screws. This side is furthest away from your house, on the outside top of your gutter.5. Trim mesh (outside of gutter) to fit.The result for me is a permanently attached mesh with inside magnetic inside strip for ease of cleaning. The magnetic strip keeps the mesh from sagging and curling, which this stuff likes to do, it is a very cheap product and needs support.Depending on storm surge results, if too much pine gets built up in certain areas I will add another layer of mesh underneath the current on an as needed basis. The top mesh is large enough to break the water. The bottom mesh small enough to stop pine needles.This solution allows me to maintain the gutters by simply pulling up on the magnetic strip. This is specifically for the flat portions of my roof.For areas of the roof that are not flat, the magnetic strip may or may not be needed, just tuck the mesh underneath the shingles as shown in the video. I’m likely going to end up tacking the magnetic strip everywhere just because of how much easier it is to maintain the gutter. I want to avoid ever having to touch this mesh product again, it’s not easy to work with. Quite happy with how things are coming along! Storm surge updates to follow!

I heard of people spending $2200 for gutter guards. I did the same thing for $60 worth of this product. It works great, stays in place and I have no leaves,no problems.

At first it was difficult to figure out how to install correctly. But once I tried a couple of ways. It was fairly easy to install and it looks good.1. Cut the screen to about at least anInch or 2 to correct length.2. Carefully Lift up the first row of shingles and tuck the screen a section at a time until it's complete to the other end of the gutter.3. First cut off the first plastic nub, away from the hook on the plastic securing clips on every piece. Reason is so that it fits underneath the first row of shingles4.Install the plastic clips below the screen, slipping it uder the fist shingles one at a time nubs up. Install at every 8 inches. Pull tight and adjust to size. See pictures.