MILAPEAK Terminal Block and Strip - 10pcs (5 Sets) 5 Positions Dual Row 600V 15A Screw Terminal Strip Blocks with Cover + 400V 15A 5 Positions Pre-Insulated Terminals Barrier Strip (Black & Red)

I like the sturdy design of these terminals, the mounting holes are deep but easy to use. The clear cover is a nice touch, but my favorite feature are the black and red terminal couplers. You can cut the couplers in half easily enough if you want to use positive and negative on the same terminal strip.

Doing a resto-mod on a rare diesel truck and had to add a couple relays during the mod part.The terminals feel solid, which gives me confidence the wire won't come loose after 100 miles.Well worth the cost.A little low on the maximum ampacity, but that is easily addressed.

Nice simple terminal strip that's worked fine for me!

Like the covers 👍

These terminal strips are nice. I mean really nice. I order a set of 4 - 8 terminal strips before I really had my project lined out. Then I realized I wanted more connections so I ordered a set of 8, 10, 12 spots. I've used all of them and they really simplified some wiring. I now land switches on one set and functions on another set and I have a set of 120v, 24v, and 12v bus strips as well as 120v Neutral and 12/24v Ground busses. The included bus strips make a snap out of building those.The screws are positive when engaged and the whole thing screws into a panel and just feels solid. I saw a complaint about the size but that size is appropriate for me. When you use heat shrink/glue fork terminals they need the spacing. If I was doing something with only small wires I might think differentlyThe cap will provide a safety cover when it's all put together.In all these are extremely well made and I laughed when I saw a single terminal strip that wasn't nearly as nice at Lowes for more than this set cost.

Built well and works well. Wire it and go.

Great selection of terminals, I have ordered 3 times now for a variety of projects

First the strip: This is for the 12 position, 15 amp strips, TB1512L. The screws are M3 (0.118 inches; like #4SAE). They have a square "washer" under the head, attached to the screw. If you remove both screws from one 'station,' the shorting bar will slide right out on one side. That could be useful if you want to have more space between wires, perhaps to segregate your wiring into groups. As the screws are M3, don't expect to apply a lot of torque! Mine seem solid, but be aware BY DESIGN each 'station' is not intended to tie solidly to the plastic housing. They float, but the screws keep them from falling out. Based on one of the answers about the product, I bought spade lugs sized for #8 screws, and they actually fit nicely, but I'd order lugs for #6 or #4 screws next time. The pitch between stations is 4.0mm. The bars across the strip at each station are about 6.5mm x .75mm cross-section, which should be more than adequate for 15A, though it's always good to derate things a bit: heating/cooling cycles can loosen screws. I like that the clear cover numbers the stations, 1-12, and that in most cases, it will be reasonably easy to probe the stations with a meter without removing the cover.But about the 3 black and 2 red shorting bars in the listing (May 2021): WHERE ARE THEY?? I see lots of reviews mentioning that the buyer didn't get them in the order, as I did not. It's not the end of the world for me, as most of my uses won't need them, but I do expect to get what was advertised. Clearly the seller should change the listing if they aren't going to supply everything they promise. That's why only 3 stars.

Por el momento tengo instalado solo el par de 10 contactos en un sistema trifásico, son resistentes pero recomiendo el uso de zapatas, porque el cable sin aislante es muy complicado de colocar en los tornillos,casi no hay calentamiento con 15A y los puentes han soportado picos de hasta 45A sin problema.

Bought these for my home automation/security project, as an electrician I do a lot of product research before hand, as electricians we can be quite particular. I decided on these even after looking at some options at the local wholesaler and was immediately impressed with the quality. Great value for the money. Most of the terminal blocks I was looking at were to big/ widely spaced for my liking, but these are perfect for wire gauges 14 and smaller, which is exactly what I needed as I’m running smaller control wires. The box they are mounted in is a 10”x10”x4”, I was able to file the ends to make them fit as it was a little tight but the plastic is good quality, I had no worries of them breaking or cracking.

They were very prompt in responding to my request to return the item because I changed my mind about my project. NO PROBLEM. Product was of quality. Recommended.UPDATENot sure yet. Sent back the product but haven't yet received my refund...