Thermal Grizzly - Conductonaut - 5 Gram - Liquid Metal Compound Thermal Paste - For Maximum Thermal Conductivity while Overclocking CPU/GPU/PS4/PS5/Xbox

I bought a 5g tube of liquid metal so I can start delidding multiple CPUs as a hobby. I have never seen such massive improvements on temperatures until I have used this! Running an i7-4790k @ 1.3V was registering 81°C, whilst the same settings, although delidded, and with this applied, the temperatures dropped to 62°C! Stock temperatures have also dropped around 17°C! A more recent project, delidding an i3-8350k, showcased a drop of 13°C on stock clocks - there's quite a bit of difference as the i3's die is smaller than the Haswell Refresh i7s. If you are considering on delidding a processor, this is probably the best material you can get! Best results on processors with larger die area!

This stuff is the bolkocks like my temps droppes 20c using liquid metal and my cpu is a i7 8700k runing at 4.8ghz volts 1.36v Standard intel burn test the first 4 passes temps onky hit 49c max and at 1.325v i7 8700k on reached max temp of 44c using intel burn test so adjusting vokts up and down is a must and doom 2016 in temps 47c max at 4.8ghz Vokts at 1.36v so awesome motherboard aorus gaming 7 z370 and belive me its good

this liquid metal it's very good, but please be carefull when you apply this thing, when i tried to get some liquid out it suddenly splashed a high amount, so i had to ''succ'' it back in, i also delided my cpu with this, it dropped almost 30*C, a good product overall. IMPORTANT: dont use with aluminium heat sinks/ coolers

the 8700k runs hot but after delidding with this stuff it has dropped to around 60c from 93c did used it between the heatsink and the cpu just to make sure i had good thermal contact. basically if you want to drop your temps big time use this stuff.

You need to be really careful when applying this Do not apply too much pressure to the plunger and be very careful and mindful of using this around other components the slightest drop could connect with small traces on mainboard

The best stuff ever. BE CAREFUL when applying, use nail varnish on capacitors nearby if applying near to the circuits :D

This is not a product for anybody other than extreme overclockers or others a lot of experience with PC building. While it does provide better cooling, there are some cons I ran across. The first being is it’s nearly impossible to pick up as it has a mercury like texture. Second, I installed my cooler on top of my processor and sat my tower up. I later noticed that this coolant leaked out onto my motherboard and ruined it. I put only a pea sized amount. Do your research before buying this as a normal paste will do just fine. I cannot give this a bad review as I couldn’t use it properly because of likely human error, however, just use caution while using if you decide this route.

Ich habe nun knapp über 20 Laptops und Rechner (CPU+GPU) damit überarbeitet und dabei keine 10 Gramm Flüssigmetall verbraucht. Das Zeug ist ergiebig! Es ist recht einfach zu handhaben. Vergesst nicht mit etwas Nagellack die umliegenden Kontakte zu benetzen um eventuelle Kurzschlüsse zu vermeiden und dann kann fast nichts mehr schiefgehen. Es wird sehr dünn aufgetragen und der Effekt ist gigantisch. Fast jeder Laptop hat nun eine 20 Grad geringere Kerntemperatur. Bspw. Ist bei meinem XPS 13 die maximale Taktrate von 2,2GHz (thermal throttling bei 101° C) auf 3,5GHz gestiegen bei ~80-85°C. Die Lüfter und Kühlrippen waren davor schon sauber und es ist so nur auf den Effekt des Flüssigmetalls zurückzuführen. Selbst bei einer guten Wasskühlung sind nochmal ein paar Grad damit rauszuholen. Das ergibt bei modernen GPUs wie der 1660 Ti oder 2080 nochmal ein paar MHz mehr Takt. Wobei ich allerdings sagen muss, dass mich das +/-1 FPS nicht interessiert, sehr wohl aber die gesunkenen Lautstärke und auch die gesunkene Temperatur. Ich benutze es auch schon seit über einem Jahr und habe noch keinen Nachteil feststellen können. Seitdem nutze ich es fast ausschließlich.

The thermal conductivity is higher than any paste I've tried before. It shouldn't be used on aluminum heatsinks. It will harden in place after a while, bonding the CPU to the cooler. Taking the cooler off after this it will be difficult and destructive. All these being said, if you never plan on changing the CPU or the cooler, this is the best way of achieving the lowest temperatures.

la arruiné al aplicar la pasta, a la mínima fuerza, se te chorrea todo, y eso me pasó, y cayó encima de todo el procesador, lo bueno es que tiene un mini tubito y pude succionar todo, el problema, es que quedó con mucho aire dentro del tubo y en mi desespero por sacar ese aire, sin querer quité el émbolo y se me cayó otra vez todo el metal en la placa, por suerte tenía un mini reciente al lado y puse todo el metal que le quedaba al tubo y fui succionando de a poco y poniéndola en el recipiente hasta que ya no quedaba nada, se formó una mega bola de como de 1x1 cm, y ya saqué todo el aire al tubo y succioné todo, lo malo es que el émbolo quedó hasta el final, así que si lo vuelvo a usar, tendré que vaciarlo en alguna parte para no regarla de nuevo, espero no se oxide, si no 1200 $ a la basura jaja

De las mejores marcas para pasta térmica y metal liquido.