Partsam 2Pcs 4.4" Amber 24 LED Turn Signal Side Marker Lights [DOT Approved], IP67 Waterproof Amber Lens Aluminum Housing Surface Mount Marker Lights for Trailer Truck Tractor RV

Extremely well build lights that are very bright. I used them for the front blinkers for an after market blinker kit that I installed in my 2016 Can-am Defender HD8 XT side-by-side. Not only do they look much better than the small 3/4” round lights that were included in the kit, they are much brighter and more visible. They were very easy to install and look great. I was very impressed with how well these lights are made, heavy duty metal frame and inclosed housing and, they put out a very bright light.

I purchased these to rewire a 78 Ford pickup bed trailer I used mostly for firewood. The original system had failed. I added new wiring and mounted these to the original taillights. Install was easy just remember each one needs the white wire grounded to the trailer frame and the wire near the plug as well. Took me a bit to figure out. I tried to run them all together and it didn't work. These lights are super bright and no more changing 1157 bulbs. Super pleased. These should work for a long time.

Super bright. Using them as reverse lights on a golf cart.

Nice cheap set of LED lights. Used them as driving lights.

I'm adding these to the inside of my truck bed, to help light it up. I own a 2020 Chevy 2500HD, and they have 2 built in the back of the bed shining forward. Ok, that's fine, but I want more light. These are pretty perfect for the job. These have an aluminum body, not plastic. The lens is stated to be poly carbonate, we'll see. These come with a plastic rubber gasket thingy....not the best, but with blk silicon, works fine. The hole size works best with a #6 screw, and I used blue Loctite on the treads. I bolted these in, not screwed in. I worry about vibration. Wiring these is a bit confusing if you didn't read the wire code in the description. WHITE is GROUND. RED is HIGH PWR. BLACK is LOW PWR, so dimmer. The wire is tipped tinned, but copper 18awg. These pull hardly any power, so I just connected into the current bed light power supply, and used too much stuff to list, but it's for future replacement needs. I sealed up the back of the wiring with sealant, and ran a bead around the outer edge to prevent leakage. Pro tip. Use a nail polish on the drilled hole in whatever you drill in. It dries fast, and will be as thick as needed to prevent rust behind these lights. Overall I like them, not super bright, but lights up well with the oem ones.

I installed these lights on my steel fender flares, (under and in. Work perfectly, and look 👀 great. Not noticeable in walkaround, but lite them up and you will be seen. Great addition to my TJ.

I installed two of these lights on the air conditioner housing on top of my camper for brakes and turn signals. This lets several vehicles behind me know I am stopping or turning. I like to camp in the mountains and the hilly, winding roads make it hard to see the original brake lights mounted down near the bumper of the camper. These are very bright.

You need to seal these with silicone, they leak, But even with that... they get 5+ stars, I love these. Note, you think you can take them apart to add silicone, you cant, you have to edge it in from the outside. But mine filled with water 7 months ago and still work like a new car LED turn signal. I can not speak highly enough of these, I just hope they seal them better, but until they do, buy them and put a tiny bead around the edge. Worth the effort.

Used on old 966 IH tractor for taillights, nice and bright

Needed to replace the lame single diode LED lights on my four year old Bailey Rangefinder caravan, which were failing one-by-one. These were easy to install, and plenty bright even on the lower brightness setting.

The lights are fairly bright despite being small. I installed them as extra reverse lights. You can use them as brake lights if you get the red ones because they have two circuits. One low voltage and one bright. UPDATE, August-2026: they still work well and the screws have not rusted, so they are actually stainless. My only regret is not buying two more, which I will do right now!

Easy to hook up with 12 V adapter. Excellent brightest for accent lighting.

Nice and bight. Nicely finished have them as running lights on my sxs. The ones on the bottom front