TRQ Front Driver Side and Passenger Side CV Axle Assembly Set 2 Piece Compatible with 2010-2012 Ford Fusion V6 3.0L 2010-2011 Mercury Milan V6 3.0L

I was very satisfied with this dual front CV axle. The quality felt solid and well made, and it fit perfectly with no issues during installation. After installation, the vehicle drove smoothly with no vibrations or noise, even during turns. It completely restored proper handling and eliminated the clicking and shaking I was experiencing. Unfortunately, snowy weather later destroyed my car, but up until that point, the CV axle worked great and performed exactly as expected—especially compared to the price my dealership wanted. Overall, it was a reliable replacement and an excellent value for the cost.

My dad's a machinist and I grew up in his shop. I've worked in fabrication, assembly, and quality control. I've personally replaced a handful of CV joint sets on various vehicles over the years, and always with automotive store bought parts. Auto parts store products carried a premium, but the quality was reliable. This was my first attempt purchasing from this company (without the middle man) and I thought it risky. My fears turned out to be unfounded. The axle assemblies are machined well and I can tell quality manufacturing and talented assembly went into the finished product. The type of steel and heat treating is correct, the splines are tight tolerance with no wiggle. The spider gear doesn't drag and it's nice and tight; same with the races & housing on the other end. The boots are surprisingly thick and a good grade of rubber. The clamping straps were even applied with care. I'm impressed, and I'm not impressed often. The ONLY criticism I could come up with is that the tool marks weren't polished off all of the steel, but that's cosmetic and would only matter on a show car, maybe not even then. It's obvious from the way these axles feel that care was taken to ensure a high quality product was shipped out. The boot clamp tabs were even neatly folded over. The entire axle was lightly oiled and placed in a thick mil plastic bag, then supported with foam braces, and placed in double thick cardboard boxes. There were instructions included, which would help a novice. The only thing better about my OEM axles is that they have rubber vibration dampers on the shaft, which the replacements don't have; I doubt I'd be able to notice the difference though. The car drives like butter compared to original axles. For the price, I think I got a bargain with this quality. I'm not sure what to do with my cores... Parts shops used to want them in exchange...

For anyone looking for an honest review here it is. Was hesitant to buy these because of some of the reviews. But considering how expensive some OEM ones are, I went for it and I am not disappointed. Purchased these for my 1998 Impreza Wagon. Heavy duty and best bang for your buck. Perfect fit. No issues at all. Took me 40 min each side. Can’t speak to longevity yet but in terms of physical quality and installation. It was great. 👍🏼

I use to think TRQ was a great aftermarket part, really love their videos and still have faith in them but only for certain parts. Shocks struts, brakes great, CV axel, nope garbage or just very bad quality control....not sure. But my driver CV shaft lasted a total of 500 miles after replacing it with this TRQ one. The passenger side is good still but after the driverside failure, I don't trust it and decided to just replace both sides to a more reputable brand so I don't have do the work all over again later on. If you're reading this, just avoid their CV axels, oh and their sway bar links, those are garbage too. Saying all that, I wouldn't say TRQ is a bad company (at least not yet, have to still try to deal with getting a refund on faulty parts that have already been installed) just that maybe they might be only good for the basics, brakes and suspension parts, not anything else!

Well packaged. Perfect fit. Easy install took about 15 minutes. Make it easy 1, turn the steering wheel right before jacking up the car. Make it easy 2, the axle nut is 36mm get a chrome 6 point socket. The impact socket won't fit into the hub. The rental tool sockets don't fit. I bought an impact socket and learned so I ran my grinder around the bottom inch or so you won't need to remove much maybe 2mm worked fine. Make it easy 3, check the axle nut there are 2 types the thin collared one that gets bent with a punch needs a torque wrench that goes to 244ftlbs. The other nut torques to 37ftlbs first pass then another 60° second pass. Make it easy 4, crawl under and look at the spot where the axle enters the transmission so you know what a fully seated axle looks like then put a tray under it in cast some fluid leaks out Un clip the brake and ABS lines. Remove the 2 bolts in the bottom of the strut. The bolt is knurled so put the socket on the nut. Back the nut off to the end of the bolt to protect the threads and tap the bolt out the other side. Push the axle through and swing the knuckle assembly to the side and hang it with a wire to protect the hose and ABS. Pop the axle out with a pry bar "NOT LEVERAGED AGAINST THE TRANSMISSION HOUSING" pull the axle out and slide the new one in. Face the split ring gap on transmission side with the gap up. Give it a tap with a rubber mallet or a hammer and a block of wood. Look underneath to be sure it's seated. Put everything back where you found it. Lower strut bolts torque to 82ftlbs. Lug nuts with factory wheels 100ftlbs. Have fun

Installed these and they’ve worked great with no issues so far. I drive a lot of dirt roads with washboards, and after roughly 800 miles, I haven’t noticed any problems. The seals are thick and made of quality material that looks like it’ll last a long time—no grease seeping through the edges. The thread on the main hub was clean and undamaged, and it even comes with a new nut. Everything went on easily, and although they fit a little looser compared to the originals, they’ve held up great. Overall, excellent seal and thread quality, very durable, and easy to install. Installed on a 2016 Ram 1500.

Semble de bonne qualité et instruction facile reste à voir la durée de vie 🤞👍

Good quality and fit perfectly on forester SJ 2015

كشكل ومضمون يبدو ان خامته وجودته ممتازه لكن للاسف لا يوافق سيارة ميركوري ميلان مديل2010 محرك6سرندل واتمنى التوضيح او تغير او حذفه من موقعه بانه موافق سيارة ميركوري ميلان مديل 2010 سعة المحرك6سرندل (انتظرت كثيرآ وبالتالي لا يوافق مركبتي وهذا في غاية السوء) وزاد السؤ سوء الى الان لم يتم اسنرداد مبلغي المالي