VIVO Universal Extending Ceiling Projector Mount, Height Adjustable Projection, White, MOUNT-VP02W

I bought this mount for my Optoma HD141x; it looks and works great! Assembly was easy, and the included wall anchors did the trick since I don't have a ceiling stud at the mounting location. Unfortunately one of the screw holes was stripped, so the set screw wouldn't tighten fully. But most set screws install in pairs so the mount is nevertheless sturdy and I was able to easily align the projected image to my screen. I guess my only complaint (if I had to make one) is that, after installing, I realized that the mount is a little too tall for my setup. I know it's my bad for incorrectly measuring, and the minimum length of the extension rod is clearly advertised, so I'm definitely not docking my rating for this. But it would be nice if they included the basic topmost joint from the VP01 model in this kit, so that I could opt to not use the extension rod at all. The attached pictures show how the mounting feet attached to my projector. Since the HD141x has 3 mount holes, one of the mount's feet should be removed. The other 3 attach according to the pics, in order to center the base plate over the projector's "do not throw away" picture of a trash can. (you'll know what I mean if you have this projector) The mounting feet fit PERFECTLY onto the projector's mount holes.

Good product, sturdy and well made. Definitely recommend to anyone who is installing into ceiling joist properly. Perfect for the price and quality.

I ordered this mount to hang my Vankyo projector and installing it was relatively simple. The instructions don't contain many words, mostly just pictures, but it's easy to follow. The only issues I found were 1) the mount comes with several sets of small screws to fit different projector types (for where it actually attaches to the projector) but the M3 screws (smallest ones) weren't long enough to reach the threading in my projector. They are 8mm and I needed longer so I just went to Home Depot and bought some for about a dollar that were 12mm long and they worked perfectly. And 2) the mount sits flush with whatever you bracket it to with only a small slot in the drop-down part for cords. If you're planning to run the cords through the drop-down and then out of the top of the mount, you'll have to either run the cables through whatever you mount to as well, or make a small notch for it to run through so it will sit flush. I was able to fix this by cutting a hole in the board I attached it to (above a drop-down ceiling). Overall, not really big issues, but just a few things to be aware of. Quality seems good and it's rock solid once installed.

Super nice ceiling mounting bracket kit for digital projector! This is made of nice sturdy metal and aluminum extruded materials with a nice white powdercoat finish. There is hardware and everything needed to install this and mount the projector. There is a ton of adjustability with the way that this bracket has been made. The bracket can also be extended for additional height adjustment. I used this in a brew house for a video presentation and mounted on some bracketing in the ceiling. I was able to tilt, rotate and adjust the projector in every possible way. The mounting brackets that attach to the projector are versatile as well and will adapt to any configuration you throw at it! Sturdy and well thought design. Two thumbs way up!

This product works well. It’s durable and holds an average sized projector. (The package says weight limit of 30 lbs.) We used it with the Epson 3800. Initially, I thought it would not work, but I ended up googling the mount and learned that we could connect three of the legs instead of four, one in the front center hole and two angled at the back holes. It was easy to mount and is very flexible for tilting to adjust your projector.

I've had projectors for the last 12 years or so. This mount has about all the customizations you could want as well as feeling good quality at the same time. Here are some issues that arose in the past using other projector mounts, that aren't issues on this projector mount: 1. Difficulty centering projector with the attachments (weight needs to be evenly distributed so that the projector mount is at the center of mass of the projector; this mount makes it VERY easy to center as well as spin the piece that actually connects to the main shalf of the mount). 2. Cords being messy / visible (this mount allows power and other cords to flow down the hollow core) 3. Difficulty installing projector after all mounts are connected. (this mount allows you to pre-bolt and then effectively just slide in the projector so that it holds all the weight as you make any finishing touches on angles / level). 4. You can increase the length of the shaft (isn't possible on all mounts). 5. You can install the mount flat on a ceiling, angled on a visible stud in the ceiling, or even side mount. I'd be concerned with side mounted projectors, but the bolts over all are long and thick enough that I believe it could hold the weight. Here are some issues you may run into using this projector mount: 1. The bolts are very thick and could result in splitting or breaking wood studs if you are in a newer house. 2. The layout of the mount for the bolts will be difficult to get more than 2 bolts in on a standard 1.5" stud (2x4) on a ceiling, I can see it requiring cutting into the ceiling and adding supports to actually hang it perfectly. 2 bolts may be enough to hold the weight just from the ceiling.

Was able to use this to ceiling mount a light Fudoni projector (this one: https://amzn.to/3O9UKsJ) and it fits fine. PRO TIP: you can remove the 4 black rubber feet on the Fudoni and that exposes screw holes. The one I received included enough screws to use to attach it, so great, covered there! Works ok for something light. The potential challenge is that the screw that holds the pressure plate that controls the extension (how far down it hangs) appears to not have any nut or backing so... if you tighten or loosen that screw on the pressure plate, the plate may forever become loose! (Design oversight!). I swapped out a bolt and nut and locking washer for the pressure plate and it works great, but unless you do that, I'd ensure you're careful with that pressure plate! I almost returned this product, but due to timeline on the install, went with my pseudo fix instead. It's a shame that plate is like that because the rest of the unit seems quite sturdy.

Great ceiling mount. Looked on Amazon and there are more expensive ones, but this one does it well also. For the price point you're getting a good value. The instructions are ok, but once you figure it out it's easy to put together, just takes a little bit of time. I didn't use the mounting screws that came in the box for the ceiling, instead I bought some heavy duty ones at Home Depot that hold about 40lbs weight capacity. The mount itself and my projector weight is roughly around 12-15lbs total. The manufacturer suggests not to exceed 30lbs total. The adjustments are easy, but you do have to use a hex screw to loosen and tighten. There's a hole in the mid piece (leg) where you can run cables through which is awesome. The leg can also extend down quite a bit if you want the projector lower. You can also adjust the legs where it will fit and screw in with most projector brands. Overall it's been sturdy and I haven't had any issues with it whatsoever. Would definitely recommend.

Excelente calidad Muy bien construido Firme y de muy buena calidad

Good Quality

All good

Bought this to mount my Epson EF12. Fits it with various mounting style to fit your need because every part is adjustable and you can shift it to match the “center” you want. The projector mounting is not completely flat but with a bit recess which is perfect to have cable in between. (I put a Mira cast puck in between).

da auch eine schnelle Lieferzeit und genau das passende