SongHe 1 Channel DC 3V Relay High Level Driver Module Optocoupler Relay Module Isolated Drive Control Board for Arduino (Pack of 5)

SongHe 1 Channel DC 3V Relay High Level Driver Module Optocoupler Relay Module Isolated Drive Control Board for Arduino (Pack of 5)

Q: I'm still not clear with the jumpers are for. What does optoisolation do here?

There are a few reasons why you would use isolation here. By the way, jumpers are for isolation - although the top jumper is futile. To use the optoisolator, disconnect the bottom jumper and connect the left pin to ground for the signal coming in to the board and connect the right pin to the ground of the voltage that activates the relay. The VCC should be connected to the voltage source that operates the relay (or if you want to remove the top jumper, vcc goes to the right pin, however it is the same as leaving the jumper on and just wiring it to the vcc input on the board. - I have used this setup to run a bank of relays off of an esp32. This allows you to run many relays without any significant voltage drop on the esp32. You will need to provide an alternate vcc for the relays. Imagine running 15 relays off of the ESP32. That would possibly cause a voltage issue on the board. If all you need to do is run 15 tiny leds (I guess 30 if you include the indicator on the board) your voltage drop would be much much lower. Because this uses optoisolation, the circuit that sends the signal (usually a microcontroller) and the voltage that powers the relay, can be totally isolated. You could use a battery for one and a computer usb for the other - no common ground between the two. -- Not pointless by any means, but the circuit setup for this is goofy and causes you to scratch your head for a minute.

Q: I put 3.3v on vcc and grounded gnd. when i put 3.3v on in, the red led lights, but the relay doesn't close. is there something i'm missing here?

It should work. You are controlling a Transistor that is operating the relay. Make sure there is enough current in VCC to activate the relay. LED will light with only 1.3v and very little current. The relay must have 3.3V VCC. Also make sure your Arduino output line has the same ground as board. Using separate power supplies can cause the problem. Otherwise, I need more details about your connection.

4.4/5

Produkt-ID: 345368604

Sichere Transaktion

Details

Connector type
Crimp
Contact material
Silver
Contact type
Normally Open
Current rating
10 Amps
Mounting type
Panel Mount

⚡3V/3.3V Power

🔌10A Load Capacity

🛡️Optocoupler Isolation

Häufig zusammen gekauft

Teyleten Robot DC 1 Channel Optocoupler 3V/3.3V Relay High Level Driver Module Isolated Drive Control Board 3V/3.3V Relay Module for Arduino (Pack of 5)

AEDIKO 4pcs DC 5V Relay Module - 1 Channel Relay Switch Board with Optocoupler Isolation, High or Low Level Trigger

ELEGOO 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Ribbon Cables Kit Compatible with Arduino Projects

Beschreibung

🚀 Power Up Your Projects with Precision!

SAFETY FIRST - Optocoupler isolation ensures your circuits stay protected.
LIMITED STOCK ALERT - Only 100 units available—don’t miss out on this essential tool!
PACK OF 5 FOR THE WIN - Stock up and save—perfect for multiple projects or backups.
POWER MEETS PRECISION - Control up to 10A at 250VAC or 30VDC effortlessly.
UNLEASH YOUR PROJECTS - Elevate your Arduino creations with this high-level driver module.

The 1 Channel DC 3V Relay High Level Driver Module is an optocoupler relay module designed for Arduino enthusiasts. It supports 3V/3.3V power and can handle loads of up to 10A at 250VAC or 30VDC. This pack of 5 modules ensures you have enough for various projects while providing essential isolation for safe operation.

Haben Sie eine Frage? Sehen Sie, was andere fragten

I'm still not clear with the jumpers are for. What does optoisolation do here?

Will 3v power the relay?

I want to run this realy on a 2 AA battery box (3v total) do i need to do anything with jumpers?

I put 3.3v on vcc and grounded gnd. when i put 3.3v on in, the red led lights, but the relay doesn't close. is there something i'm missing here?

Häufige Fragen

TrustPilot

TrustScore 4.5 | 7.300+ Bewertungen

Rajesh P.

Der Kundenservice war hervorragend, als ich Fragen zum Produkt hatte.

vor 2 Tagen

Ali H.

Schneller Versand und hervorragende Verpackung. Das Leatherman-Tool fühlt sich sehr wertig und stabil an.

vor 1 Tag

Sehen Sie sich alle Überprüfungen von TrustPilot an

Kaufen Sie weltweit ein und sparen Sie mit Desertcart

Preis-Leistungs-Verhältnis

Wettbewerbsfähige Preise für eine große Produktpalette

Kaufen Sie weltweit ein

Wir bedienen Millionen von Käufern in über 100 Ländern

Verbesserter Schutz

Vertrauenswürdige Zahlungsoptionen, die bei Käufern weltweit beliebt sind

Kundensicherung

Vertrauenswürdige Zahlungsoptionen, die bei Käufern weltweit beliebt sind.

Desertcart-App

Shoppen Sie unterwegs, jederzeit und überall.

€ 34.37

Zölle & Steuern inkl.

GERMANYspeichern

Kostenloser Versand

with PRO Membership

Kostenlose Rücksendungen

30 Tagefür PRO-Mitgliedschaftsbenutzer

15 Tageohne Mitgliedschaft