Transparent Clear Joycon Handheld Controller Housing (D-Pad Version) w/Full Set Buttons, DIY Replacement Shell Case for Nintendo Switch & Switch OLED Joy-Con – Console Shell NOT Included

These look great. I had two matching pairs of boring grey joycons. Now one pair is a grey transparent with colourful buttons! Installation was tricky (which I kind of enjoy - working on small electronics is satisfying for some people!). I broke one joycon while installing - I think I must have shorted out the main board on it. Take your time installing! The right controller is much more complicated than the left, so maybe start with the left and figure out what you're doing then go to the right one. Fortunately a replacement joycon was inexpensive on ebay and on my second try they both seem to work great. Installation was not a fault of this product, they supply replacements for all of the screws and springs, as well as good quality (especially for the price) screwdriver and bits for the job. Would do this again! Would just be a little more careful the first time! Thanks !

I've modded my 3DS and GBA SP, as well as various controllers and the right joycon is one of the more difficult swaps I've done. If you are patient and gentle and follow a video guide you should be fine. Just a few things of note: There are about 6 tiny and fragile ribbon cables with tiny clips on each joycon. They all detach and reattach differently, which is why I reccomend a video (or take a video/pictures of how and how far the cables go in before they are clipped in place. Some have bumps to indicate, others do not. I had two I thought were in place pop out as I went on to the next step. Again, why I reccomend a video over a quick guide with some pictures. The rz and lz require a little force to remove from the old piece so I held my breath a little there. Other than that it wasn't too bad and the left joycon is much easier than the right so maybe do that first to get an idea of what's to come with the right one. Only weird thing was there are these 4 screws that form a square and 2 screws are short and 2 are long, so don't mix those up. Overall looks great and feels as good as the priginal buttons, but the D-Pad feels amazing compared to the original 4 button setup. I ended up using all the original screws but it comes with everything you need (even springs) as far as I can tell.

The Shells replacement from eXtremeRate are the best shell replacements in the market, the offer some options for the aesthetic of the control, some buttons to be replaced with a different color or like in the joycons, changing the awful left joycon individual butons for the D-pad, to a real D-pad, you have different color options as well, transpared or solid colors, the build quality is really good, the plastic is firm and solid, is not cheap plastic like other options.

Plastic feels more brittle than stock Joycon shells, but looks good and was easy to swap. Love the inclusion of the D-pad and colored buttons.

Perfect fit. Love the D-Pad option! Nice quality.

I’m a complete beginner to this kind of thing. I’ve never done this before. Here’s my tips for people in the same position The Y screwdriver included doesn’t fit. It will ruin your screws. You need to buy a Y000 screwdriver separately. Also make sure you’re watching a YouTube video on how to do this. Make sure you have good, narrow and tiny tweezers. Maybe use a magnetized bowl to keep screws and springs in. Also, you don’t have to remove every cable from the motherboard. If it’s possible to leave them attached, I recommend doing that. I ruined a shoulder button cable and had to buy a new one. It’s easy to remove and put back the joycon and battery cables. But other than that, if you want to be extra careful, maybe don’t try to remove anything else. I almost broke the vibration part by trying to take it out. Just leave it. Overall, it’s not hard. Admittedly I did break a cable, but after learning that I didn’t have to take all the cables off the motherboard like they did in the videos, I was fine. The first joycon may take a long time since it’s your first time, but the second one will go by much faster. I dropped so many screws and buttons and almost lost them for good. DON’T DROP YOUR BUTTONS or screws. In the YouTube videos, they recommend you have a small plastic pry tool called a spudger. I personally used a guitar pick for this. It wasn’t quite the same, but it was good enough. I have really small hands, too, so I didn’t need the tool as much as other people might. If you have big hands, look into buying a spudger. Ok that’s it. Sorry this was super unorganized. You can do it. If I can do it, you can. Just take all these tips and use them. (Get a Y000 screwdriver Have narrow tweezers Have a magnetized screw bowl Don’t remove every cable from the motherboard Don’t drop any screws or buttons Have a spudger of some kind Watch the YouTube video by FetchingTech)

どうにか取り付けられた。 多少故障した。(笑)

Estas carcasas son para sustituir las carcasas originales de la switch, hay que tener paciencia y un poco de maña y delicadeza al montarlas, buen precio y buena calidad.

Bellissimi cover in sostituzione agli originali , effettuato il reso solo per la mia poca esperienza nel montaggio . Prodotto davvero molto bello

Cette coque est parfaite pour les joy-cons. Les miens étaient tout blanc et se salissaient très facilement. Mais grâce à ExtremeRate non seulement ils sont devenus transparents mais super agréable à prendre en mains. Dans la boîte, on retrouve deux tournevis un pour les vis externes et l'autre pour les vis internes. Il y a même des ressort de rechange pour les gâchettes ainsi que deux types de D-Pad, un en tout noir et l'autre au coloris de la coque choisie. Le tout est très bien emballé. Je recommande vivement.

At first I was anxious to order, I thought it will be another nightmare on shipping. But I bit the dust anyways, the shipping went well, with tracking also from Aramex. The shell looks very good and fits very well as if it was the original. Never regret buying this ExtremeRate shell, I will be buying the Atomic Purple next time for nostalgia on the Gameboy Color. The D pad is very good addition also, it has the feel that of the XBOX one controller. The extra screws, springs are very good to have as well when u find yourself losing the originals. Note: Do not over tight the screws as they will be very visible on transparent shell.