LAVIEVERT Wooden Multi-Craft Weaving Loom DIY Hand-Knitting Weaving Machine Intellectual Toys for Kids

This is quite a serviceable loom, and its simplicity makes it easy to upgrade. My review is based on its usability and price--the nitpicks and proposed solutions below would only count against it if the price were significantly higher--at which point I may as well just buy a full size table loom (lightly used is significantly cheaper than new).This loom is unfinished. It is surprisingly smooth in most places and obviously sanded, but there are a few rough areas and small spots that get crushed when folding (see detail photo). At some point I will want to take it apart to sand and apply a protective coating. It also started squeaking halfway through the practice materials, so I'll take that opportunity to oil the moving parts as well.I like that this loom folds up neatly even with a project in progress, making it portable and space efficient. It is pretty sturdy, so I would be comfortable stuffing it in a canvas tote and not worry about bumping it a little.The practice materials it comes with are very basic, and almost certainly synthetic. It amused me to see that the empty shuttle had a longer curved slot than the ones the three solid colors were loaded on. The shuttles can be more efficiently loaded using a figure 8 on each side (see the yellow shuttle in my photos demonstrating this), as well as the center winding shown in the listing.Make sure to even out the warp tension before you begin (you can look it up on the internet). I used some thick paper in between layers to keep the outer threads from sneaking in between the inner threads and making it wonky. When finished with the practice material, make sure to look for a paperclip and a pair of pliers: unless you plan to tie the next warps to the existing ones and pull them through, you'll need a hook to warp your next project.The weaving width on this loom is 6" and its reed (beater bar) is 4.25 dpi (dents per inch--I measured exactly 17 dents across 4 inches), which is better for bulkier warps. It has two shafts with offset heddles of the same dpi, secured with the same twine as the preloaded warp thread. These could probably be upgraded/improved by anyone who can drill even holes and glue small sticks to two horizontal bars. I plan to use skinny craft sticks and some wooden dowels for mine.The gears that secure the warp and cloth winding bars are on opposite sides, which means that the working width was decreased by almost an inch on each side. When I take it apart to sand and finish, I plan to flip one over to get an inch back, for a total weaving width of 7".The reed (beater bar) is pressed into the cloth at an angle that makes it hard to see where the pick (weft thread) will go, and thus makes it hard to control your ppi (picks per inch). This one might be hard to fix, but I think it is doable: change the angle that the reed rests in the arms so that it faces up higher, or mount the arms at the top instead of the bottom of the loom. I'll have to experiment and see what works for this.Finally, about weaving knowledge: weaving is a skill. The preloaded warp and simple design make it easy to use, but don't expect an item so cheap to teach you all setup and finishing steps of a notoriously complicated hobby. That manual in itself would be a book (in fact, there are many). If you're able to access Amazon shopping and reviewing, chances are you're connected to the internet. On the internet, one can find a variety of different perspectives, which makes it a good starting place to learn. If you want better guidance, there are plenty of weaving guilds that offer classes--ask around your area.

It was easy to assemble. I had seen a review of it by Kelly Casanova on YouTube. So I knew that I would probably have warp tension issues and I did. I took the tension off and removed the front tie on rod. I then removed the warp threads and cut the loops. This way I was able to tie the warp and even the tension. As you can see from the pictures, I have good tension and able to get a decent shed in either heddle.I have a couple of Rigid Heddle looms. After seeing Kelly’s review I thought it might be fun to have this little loom as a sampler to practice, experiment.I’d recommend this loom . It’s actually well built and I love the design. Be sure to watch Kelly Casanova on YouTube. It will help you learn how to weave and how to re-warp this loom. Have fun!

Very compact, easy to store and simple to put back together, easy to use once you have read the relatively small instructions they give you. Definitely could come with a bit more instruction, especially in regards to warping the loom. Good price, easy and simple. Yarn is functional for a beginner albeit basic colors. Altogether a good purchase.

It has issues, but if you're just learning and testing out whether you like weaving or not, this is the best price point! Everything else is way too much money just to test it out.The issues: the heddles (blue pieces that move the yarn up and down) are wonky and assembled unevenly. It's easily fixed, but a tedious job. It comes pre-warped, but very poorly done. Again, easily fixed and tedious.Watch some YouTube videos if you don't know anything about weaving. And then watch some more. The more you watch, the more familiar you get with the weaving vocabulary and how it's supposed to work.I've never woven before, but I'm glad I started with this little loom, because I didn't have to dump a load of money on something I didn't know whether I'd like it or not.I'm really enjoying learning on this loom. And it can fold, making it portable. I replaced the two screws on the sides with bolts that have knobs so they're easily removed and allow it to fold. (Look up M6 knob screw.) This makes it easy to put away or take with you anywhere.Recommended.